Replacement Gel probe for pH1000A meter

• Large double line LCD display with backlight
• Display closer to the surface of tester for a better viewing angle
• Simultaneous display of measurement and temperature
• Easy-to-operate user interface with the addition of the MENU key
• 1 push calibration cap
• Leakproof
• Fill-line indicator for measurement
• Wider, stable base to stand the tester upright

• PVDF body
• Open junction reference
• Conical glass tip
• 3.5 mm connector

• HI-2202 edge®blu pH Bluetooth® Meter with HALO™ HI-11102 gel-filled Bluetooth electrode
• Two USB ports
• Store up to 1000 log records of data
• GLP Data of the last calibration you perform is stored
• Capacitive touch keypad
• Easy to read 14 cm LCD with wide 150∞ viewing angle
• CAL Check™ technology to warn you if the electrode bulb is not clean or if the buffers are contaminated during calibration

• Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)  
• 0.01 pH resolution
• Offset and average slope display 
• Automatic / manual temperature compensation and temperature calibration function
• ORP calibration option
• °C & °F temperature readings
• Auto log data; built-in memory can store up to 500 data
• Auto shut-off (programmable: up to 30 minutes)
• Auto stable, auto hold, and real time measurement modes
• Calibration alarm (programmable: up to 90 days)
• Built-in electrode holder allows 2 electrodes to be attached
• Monochrome LCD with white LED backlight: 50 x 50 mm
• Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip
• Powered by 2 x AA batteries
• Packaged with electrode and calibration solutions in carrying case
• 3 years meter warranty

• Easy to use
• Non-volatile memory
• Large, upright LCD
• Click-lock battery compartment
• Easy push-button calibration
• Transparent protective cap
• ±0.1 % accuracy across full pH range
• Auto-buffer recognition
• Auto-calibration functions
• Long-lasting sensor

• Conic tip
• 3.5 connection
• Easy to use
• Glass body
• 6 months warranty

• pH measuring range 0 to 14
• IDS pH combination electrode with gel electrolyte, plastic shaft and integrated temperature sensor
• Safely measured values due to signal processing in the sensor
• Easy electrode replacement thanks to calibration data stored inside sensor
• Sensor quality monitoring by QSC function

• Simple menu
• ISM® Compatible
• uFocus™
• T-pad
• Endpoint signalling
• IP67 - (weatherproof)
• Outdoor mode (maximises battery life)
• Sunlight-proof

• Waterproof
• Automatic or manual temperature compensation
• Calibration
• 200 hour battery life approximately with 1.5V AA batteries (x4)
• Clear display
• Auto hold
• Calibration timeout
• PC Connectivity via USB
• GLP
• Intuitive keypad
• Carry case and accessories

• Replacement sensor for the B-713, pH 11, ph 22, pH 33
• Employing the same test principle as standard laboratory electrodes, the LAQUAtwin packs all components into a flat sensor that’s less than 1 mm thick.
• Waterproof construction protects the instrument.

• Rubber Boot protects against knocks and hits
• Easy-To-Read Display
• Customised LCD screen
• Tactile Keypad with a simple, straight forward design for easy operation
• Compact Design Fits Your Palm Perfectly - Designed for easy single-hand operation
• Convenient Benchtop Stand
• User-Friendly Diagnostic, easy to understand trouble-shooting prompts
• Splashproof & Shock-Resistant Built with shock-resistant
• ABS plastic and protected by an IP54-rated housing against accidental splashes
• Hold function freezes readings momentarily for easy viewing and recording
• Energy and Cost Saving - Switches off automatically after 20 minutes of inactivity
• Automatic Temperature Compensation
• Accurate readings, even under varying temperature conditions
• Non-Volatile Memory -Meter settings are saved, even when batteries run out

• Stainless steel blade
• 3.5 connection
• easy to use
• PVDF construction

For testing of waste water.

• Easy-to-operate, robust pH/mV-meter with large LCD-display, for mobile routine measurement.
• Meter in carry case with
• pH-sensor SenTix™ 41
• buffer solution STP 4 and STP 7
• stand, beaker
• short instruction manual
• CD-ROM and batteries
• Handy case sets for field applications
• The ProfiLine handhelds are available as single instruments in a case without measurement accessories, but also as sets supporting individual application requirements.
• The case also serves as a small field laboratory.

Spear-type pH combination electrode for penetration measurements in meat, fruit and cheese, with fixed cable and waterproofed DIN plug.

Buy together with XYL-WTW-903843 to use as a puncture knife pH probe.

• Simultaneous pH and temperature measurements on a large dual-line LCD Display
• Automatic pH calibration at one or two points within two memorised buffer sets (standard or NIST)
• Selectable temperature unit (℃ or ∞F)
• Electrode condition indicator
• mV of pH measurement for electrode check
• FC2323 dedicated pH with an integral temperature sensor
• Probe quick connect system
• Battery life indication and low battery detection
• Keystroke confirmation tone
• Auto-off function
• Waterproof casing IP67